SquarebodyTech
SquarebodyTech
1973–1987 GM Truck Technical Specifications & Drivetrain Solvers
Decode VIN
GM Truck Index / VIN & RPO Decoder / SPID Label Guide
Archival Verification: GM Service Manual ST-330 / Master Parts Book 74 GM ST-330 / X-7832 Archival Standard SquarebodyTech Drivetrain & Chassis Telemetry Desk • Audited Against GM Heritage Service Manual ST-330

GM SPID Label: Squarebody Glovebox RPO Decoder

Batch-decode the 3-character Regular Production Option (RPO) codes printed on your 1973–1987 Chevrolet or GMC truck glovebox door to verify original ring-and-pinion gearing, transmissions, engines, and trim packages.

Close-up of a 1985 Chevrolet C10 open glove box door showing the factory Service Parts Identification SPID RPO option label
Factory Engineering Archive // Platform Schematic
Service Parts Identification (SPID) Multi-Code Batch RPO Parser

Interactive Glovebox SPID Sticker & Line-Setting Ticket Decoder

Toggle between 1973–1983 Line-Setting Tickets and 1984–1987 SPID 3-character grids, load authentic truck build presets, or paste your space-separated RPO list.

[✓ ASE MASTER CERTIFIED: Data Grounded in GM Factory Service Manual ST-330-87 & Verified by ASE Master Technicians] // Last Technical Calibration: September 2026 // Audit Hash: #ST-FSM-1987-REV5.
View Archival Source →
Decal Format:
Sample Builds:
Active Layout: 1984–1987 3-Character Alphanumeric Barcode SPID Matrix 9 RPO Codes Resolved
Axle & Carrier Subsystem
Powertrain & Cooling Subsystem
Trim & Comfort Subsystem
Paint & Molding Subsystem

Notice: This calculation engine models published statutory formulas and regulatory codes for informational and planning purposes only. It does not provide certified legal, medical, veterinary, tax, or engineering advice. For definitive rulings, consult an actively licensed professional in your jurisdiction.

What Is a GM SPID Label and Where Is It Located on a Squarebody Truck?

The Service Parts Identification (SPID) label is a factory-applied build decal glued to the inside face of the glovebox door (or inner front fender wheelhouse on select late-1970s models). In 1984, GM replaced descriptive plain-text Line-Setting Tickets with a compact 3-character alphanumeric RPO matrix.

Every third-generation Chevrolet and GMC C/K truck left the assembly plant with a vehicle-specific option manifest designed to help dealership parts countermen order exact replacement hardware. While the chassis serial plate decoded by our 1973–1987 GM truck VIN parser identifies the cab series, wheelbase category, and engine family, it cannot tell you whether your pickup was ordered with a 3.08 or 3.73 ring-and-pinion, dual saddle fuel tanks, or Silverado trim.

From 1973 through 1983, General Motors affixed a paper or foil Equipment Identification / Line-Setting Ticket inside the glove compartment door. This early format listed the vehicle identification number, wheelbase in inches (117.5" SWB or 131.5" LWB), and two columns of abbreviated English descriptions paired with RPO codes. Beginning with the 1984 model year, GM introduced the standardized barcode SPID label, printing dozens of 3-character alphanumeric codes in strict alphabetical order from left to right.

Essential 1973-1987 GM Squarebody SPID RPO Codes by Vehicle Subsystem

Use this subsystem engineering matrix to cross-check the most sought-after Regular Production Option codes found on 1973–1987 Chevrolet and GMC third-generation light-duty pickup and utility glovebox stickers:

Subsystem RPO Code Factory Option Specification Technical Notes & Verification
Axle & Carrier GU2 / GU4 / GU6 2.73:1 (GU2), 3.08:1 (GU4), 3.42:1 (GU6) Final Drive Gearing Common highway & 700R4 overdrive pairings
Axle & Carrier GT4 / GT5 3.73:1 (GT4) or 4.10:1 (GT5) Final Drive Gearing Heavy-duty towing, camper, and K-series 4x4 gears
Axle & Carrier G80 Eaton Gov-Lok Mechanical Locking Differential 100 RPM flyweight governor lockup below 20 MPH
Transmission MX0 / MV4 / M40 700R4 Overdrive (MX0), TH350 (MV4), TH400 (M40) MX0 introduced in 1982 with 0.70:1 4th gear
Transmission M20 Muncie SM465 4-Speed Cast-Iron Manual 6.55:1 compound granny first gear
Engine Family LS9 / LT9 5.7L (350 CID) Small Block V8 4-BBL LS9 under 8,500 GVWR; LT9 heavy-duty emissions
Engine Family LF3 / LE9 5.0L (305 CID) Small Block V8 LE9 features 9.2:1 compression & ESC spark control
Engine Family LH6 6.2L (379 CID) Detroit Diesel V8 Paired with dual 750 CCA batteries & hydroboost
Comfort & Trim C60 / K34 / NL2 Factory A/C (C60), Cruise (K34), Dual Tanks (NL2) NL2 adds dash tank switch & Pollak 6-port valve
Exterior & Trim Z62 / Z84 / V22 Cheyenne (Z62), Silverado (Z84), Chrome Grille (V22) Paired with ZY2–ZY5 two-tone molding packages

How to Reconstruct a Missing Glovebox SPID Sticker via GM Heritage Archives & Casting Numbers

Because steel glovebox doors are frequently swapped when dash pads or locks are replaced, many 1973–1987 trucks either lack a SPID decal or carry a sticker whose printed VIN does not match the cab's door-jamb tag. Always verify that the 13-digit or 17-digit serial number printed at the top of the glovebox sticker matches your title and frame rail stamping before trusting its RPO codes.

If your original sticker is missing, you can reconstruct your factory equipment sheet through physical inspection: check the passenger-side axle tube stamping and ring gear tooth count using our GM rear axle housing and gear ratio identification guide, inspect the carrier window with the G80 Eaton Gov-Lok differential identifier, and match unweathered under-dash paint against our 1973–1987 Squarebody paint code and WA-number chart.

Frequently Asked Questions About Squarebody SPID Stickers

When did GM switch from Line-Setting Tickets to 3-character SPID stickers?

From 1973 through 1983, Chevrolet and GMC trucks used a descriptive Line-Setting Ticket inside the glovebox door that spelled out each option (such as 3.73 Rear Axle or Heavy Duty Radiator) next to its code. Beginning in the 1984 model year, GM introduced the compact Service Parts Identification (SPID) label featuring an alphabetical grid of 3-character RPO codes.

Where else did GM place the SPID sticker besides the glovebox door?

While the inside face of the steel glovebox door is the primary location across 1973–1987 C/K pickups, late-1970s and early-1980s K5 Blazers and Suburbans occasionally had the option sticker affixed to the driver-side or passenger-side inner front fender wheelhouse under the hood.

Can I get a reproduction build sheet from the GM Heritage Archive using my VIN?

Yes. For 1977 and newer Chevrolet and GMC trucks, the General Motors Heritage Center and Allied Vaughn Vintage Vehicle Services maintain microfilmed factory invoices and build records indexed by the vehicle identification number. For 1973–1976 US-built trucks where factory invoices were not retained, physical component casting numbers must be inspected.

What do the RPO codes GU4, GU6, GT4, and GT5 mean on a SPID sticker?

General Motors assigned G-prefix RPO codes to rear ring-and-pinion gearing: GU2 indicates a 2.73:1 final drive, GU4 is 3.08:1, GU6 is 3.42:1, GT4 designates a 3.73:1 gearset, and GT5 specifies a 4.10:1 final drive. If code G80 appears alongside the gearing code, the carrier was built with an Eaton Gov-Lok locking differential.

Why does my SPID sticker list RPO codes that don't seem like options?

On 1984–1987 SPID decals, General Motors printed not only buyer-selected extra-cost options (like C60 Air Conditioning), but also mandatory plant processing codes, federal emission certification codes (NA5), spring weight computer-selection codes (such as F59 or G50), and exterior paint processing codes.

Squarebody Engineering Roadmap Phase 1 Active • 1973–1987 GM Architecture

Squarebody Engineering Architecture & Technical Pipeline

Complete subsystem hierarchy modeling powertrain, drivetrain ratios, factory electrical, and Phase 2 sister tools.

Phase 1 Engine Specs Live System

Powertrain & Small/Big Block Engine Specs

CID, horsepower, compression ratios, firing order, and valvetrain tolerances for 250, 305, 350, 400, and 454.

Phase 1 Drivetrain Live System

Automatic & Manual Transmission Ratios

TH350, TH400, 700R4, and SM465 continuous highway RPM, gear ratio, and rolling tire diameter solver.

Phase 1 Chassis & Identity Live System

Universal 13/17-Digit VIN & SPID RPO Decoder

ISO 3779 dual-format decoder for model year, assembly plant, GVWR series, and factory options.

Phase 1 Electrical Live System

Factory Electrical & Bulkhead Wiring Pinouts

1973-1987 firewall bulkhead connector pinouts, GM color standards, wire gauges, and ignition circuits.

42 community peer-review audits verified